Tag Archives: PSA

ARBuilds, Reviews / For Sale, Uncategorized

Top Four PSA AR-15 Kits

Hi folks. I like building AR rifles and sometimes I just want a kit with all of the parts. Sometimes I will then swap stuff out and the original parts go in a bin but they are nice to have as spares and sometimes I will build the kit with the included parts – it just depends on my mood and budget to be perfectly honest. For years now, my main source for kits has been Palmetto State Armory (PSA) headquartered in Columbia, SC.

I almost always get my stuff off their website but they do have some very cool retail stores scattered around South Carolina. I had an opportunity to go to one a couple years back and it was very cool. Unfortunately, I lacked funds at the time and just picked up a couple of items. A person could put a serious dent in their credit card by going in one of their stores … or their website for that matter 🙂

People used to complain that they were slow to ship and to respond. First off, I always knew they were trying to keep costs low – they always shipped and they did respond – just not right away. For over a year now, I have noticed they are far faster at shipping – sometimes even the same day – and they are also faster at responding. So, if you hear bad stuff about this, I wouldn’t worry about it.

I’ve also heard people question their quality. Folks, if you want a tier one rifle, go buy a tier one rifle or the parts from them. Palmetto gives you a decent combination of quality and price. For folks planning on hunting and target shooting with their friends, I have no reservation to recommend them. If you are shooting in competition or planning to use this rifle in some kind if law enforcement situation or somewhere that requires high reliability, I think you probably need to look at the higher end ARs that are designed to handle tens of thousands of rounds. Look, I’m just being candid – the PSA AR rifles and pistols are solid but they have a different intended audience. There are reasons besides “coolness” where certain buyers must move to suppliers like Daniel Defense, BCM, Knights, LMT, H&K, LWRC, etc.

At any rate, back in April of this year (2021), I asked what their top four complete kits were (meaning everything except the lower receiver) and they had a list! If you like building AR kits like I do, I thought you might find this interesting in terms of what is included:

PSA 16″ 5.56 NATO 1:7 MIDLENGTH NITRIDE 13.5″ LIGHTWEIGHT M-LOK MOE EPT RIFLE KIT W/ MBUS SIGHT SET (Model 516446780)

PSA Model 516446780

Noteworthy here is the entry level Magpul MOE buttstock and grip plus Magpul MBUS flip up sights. They are also including a PSA EPT fire control group – this means that the trigger and hammer have nickel boron finish causing them to move easier because friction is reduced.

It has one of the PSA 13.5″ long handguards set for M-Lok attachments. Everything else is typically found in any of their AR kits with a collapsible stock. They make and restock these kits all the time.

The price as of this writing is $669.

PSA 16″ M4 CARBINE-LENGTH 5.56 NATO 1:7 NITRIDE 15″ LIGHTWEIGHT M-LOK FREEDOM RIFLE KIT (Model 51655106915)

PSA Model 51655106915

Despite a cool looking 15″ handguard, this is a basic AR and you can replace the grip and buttstock later if you want. It’s selling so well that PSA is out of stock right now but you can be notified when it is back in stock. They tend to make and restock these kits all the time.

The price isn’t listed right now since they are out of stock but I would expect it to be slightly less than the first kit – unless they are charging a premium for that handguard.

PSA 16″ M4 CARBINE-LENGTH 5.56 NATO 1:7 NITRIDE 15″ LIGHTWEIGHT M-LOK FREEDOM RIFLE KIT (Model 5165450384)

PSA Model 5165450384

Definitely a basic 15″ railed rifle kit. Everything looks entry level but you can always customize it down the road if you want.

Again, no price as they are out of stock. I’d expect it to be cheaper than the two kits above. You can sign up to be notified when they do get it in stock if you want. They tend to make and restock these kits all the time.

PSA 16″ MID-LENGTH 5.56 NATO 1:7 NITRIDE 15″ LIGHTWEIGHT M-LOK CLASSIC RIFLE KIT WITH MBUS SIGHT SET (Model 5165491598)

PSA Model 5165491598

This one has the Magpul BUS sights, an interesting looking handguard … and that’s about it. Everything else is what you tend to see in any of their basic AR rifle kits with collapsing stocks.

The price as of today s $649.99

What rifle is in the top photo?

It started out as a PSA 16″ kit. It had an Anderson lower, WMD bolt, and a Magpul ACS-L stock – I like those because they lock in place and don’t rattle. It had a BMC Mod 3 charging handle, Vortex 1-6x scope on a Vortex 2″ offset mount, YHM extended push pins and a PSA ambidextrous selector lever. The fire control group is one of the PSA EPT sets – I do like them for basic triggers. I like Geissele SSA-E triggers the most though. I honestly don’t recall who made the offset sights.

Conclusion

If you’re looking to build a decent entry-level rifle from a kit with all of the parts you need other than the lower receiver, the above should work great for you. At a minimum, they will all give you a foundation to start with.

Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Sniper / Precision Rifles, Surplus Rifles

PSA Has Some Cool Rifles In: 7.62×51 Galil Ace, FIME Molot RPK-74 and Breda M1 and M1D Garand Rifles – Wow!

I have and IWI Galil Ace rifle in 7.62×51 NATO and it’s exceptionally well made. I notice that IWI has it in and an Italian version of the Garand known as the “BREDA” in 7.62×51 also. I thought I would spread the word – I sure wish I had the funds to buy both models of the BREDA.

IWI GALIL ACE 7.62 NATO SEMI-AUTO RIFLE, BLACK – GAR1651

ITALIAN BREDA M1D/ TIPO-2 T.S. GARAND WITH M84 SCOPE AND CRATE, VERY GOOD SURPLUS CONDITION – BREDAM1S

ITALIAN BREDA M1D/ TIPO-2 T.S. GARAND RIFLE 7.62X51, VERY GOOD CONDITION – BREDAM1

Just to make the lack of funds hurt even more, they have a FIME Molot RPK-74 in stock also. Where these came from, I don’t know but they command a princely price.

IWI GALIL ACE 7.62 NATO SEMI-AUTO RIFLE, BLACK – GAR1651

If you are looking for one of the above and can afford it – rock on! I hope this helps you out.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Self and Home Defense, Self Defense, SIG

PSA Has a Good Deal on the SIG P365 Tac Pac With 3 12-rnd Mags and a Holster

Folks, Palmetto State Armory has a deal going on where you can get one the excellent SIG P365 pistols in what they call a “Tac Pac”. Normally the Tac Pac just has a couple of mags but this deal includes three real SIG 12-round mags that often go for $35-45 each and a combination Inside the waist band (IWB) or outside the waist band (OWB) holster.

This is the PSA deal. Note, the photo in the ad shows a 10-round magazine loaded and the three 12-round magazines but to be clear, the deal is for three magazines and not three plus one. The photo at the top of the post is my personal P365 with a 12 round magazine inserted.

The Sig P365 is rated for +P 9mm ammo and is my every day carry. I can tell you that I have never had a failure to feed or extract with the pistol and have fired Hornady Critical Duty +P, Federal HST +P, all kinds of 115gr and 124gr FMJ ball ammo, etc. It just east whatever I give it and is reliable – that’s why I rely on it to protect my family when we are out and about and discretion is required – it’s an ideal concealed carry pistol.

I really like the 12-round magazines. The small plastic fitting on the bottom is ideal for my to put my pinky finger on and I wear size XL gloves. The 10 round magazines are even shorter. Most of the time I am carrying using a 12 round magazine. They do make a 15 round magazine but that sticks out a tad more than I care for.

Note, go for real SIG magazines. Some of the aftermarket ones, such as Promags, don’t get as good of reviews.

I can’t speak first hand to the holster they are including though – I use a soft Desantis 106 IWB holster and a High Noon shoulder rig. Given the holster is from SIG, I would expect it to be good enough to get started with.

At any rate, it’s a very good deal so click here to learn more.

Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

The following are various listings for SIG P365 pistols and accessories so you can scroll through and look at prices.

AK & Related Rifles, USA

PSA AK-E: First Range Trip

Well folks, we finally had a chance to go to the range for the first time this year. It was a beautiful day and the only shortcoming was that we had a number of rifles and pistols to test and not enough time to shoot a ton of rounds through each. To be honest, we had a blast 🙂

One of the rifles that went was my PSA AK-E. It was the smoothest cycling AK out of the box that I have encountered and I think it’s due to a combination of pretty good fitment and their nickel-boron coating of the bolt and bolt carrier. I’ve written a number of posts about my journey with the AK-E so click here to open a tab/window and see those posts.

Palmetto State Armory (PSA) has a stunning array of Kalashnikov firearms now. AK-47s, AK74s, 100 series, rifles, pistols … it’s impressive. Click here to go to their main AK menu.

We were shooting 124 grain 7.62×39 FMJ ammo by Golden Tiger. This is great ammo and my favorite to use. For AK bulk ammo, it’s relatively accurate, reliable and consistent — notice that I say relatively. It will hold its own with any of the bulk steel case ammo or even do better. I’m not comparing it to hand loads or specialty ammo.

Niko is a heck of a shot and is familiar with AKs as well. He had to do Slavic Squat shot 🙂

I wish I could tell you that we shot hundreds of rounds but there just wasn’t time. We shot three mags through it – 90 rounds and did not have one problem. Yeah, it’s not many rounds but I figured some of you would like an update and I’ll post again after the next range trip.

Observations:

  • The little Vortex Crossfire did a great job and we had fun punching paper. The scope and the RS!Regulate optic mount worked out just fine. I’ve used the combo before and expected such.
  • The rifle functioned just fine with no feed or ejection problems
  • The rounds were grouping pretty well – we were not shooting for accuracy – more for function testing
  • The trigger was very nice – ALGs are great in general and what I like to use these days.
  • The brake did a decent job. I think a JMAC RRD-4C brake would have reduced recoil further but out of the box the recoil was not bad at all. When you think about it, even an AK with no brake is surprisingly pleasant to shoot during semi-auto fire
  • I definitely liked the feel – the weight and balance – of the rifle – the RS!Regulate handguard, our AK-12 grip and a Magpul ACS stock worked very well together
Me with my favorite AK shooting shirt 🙂

When we were done, I did take the rifle apart and did not see anything concerning. So, I definitely want to shoot it more and the rifle is off to a good start.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

AK & Related Rifles

PSA AK-E Part 5: The End Result

1 Comment

This is the final post of the series. Here are the previous AKE posts listed so you can view them if you so wish:

In this final post, I want to share a series of photos of the end result:

By the way, the sling you see is from S2 Delta. I have a number of their slings now and they are nicely done. You can pick them up on Amazon.

Palmetto State Armory (PSA) has a stunning array of Kalashnikov firearms now. AK-47s, AK74s, 100 series, rifles, pistols … it’s impressive. Click here to go to their main AK menu.

Conclusion

This is it for now. Hopefully when the Corona Virus stuff calms down I’ll be able to take it to the range. I’m betting it’s going to run real nice based on how it feels.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

AK & Related Rifles

PSA AK-E Part 4: Customizing The Rifle

In the past three posts, I covered some of the reviews I read, initial observations out of the box, and a more detailed look and the internals. Now, I’ll cover the customization work that I did. For me, the AK-E was always going to serve as a base platform to build on. I wanted to showcase both one of our AK-12 grips and one of our new AKM gas tube covers. So, let’s step through the modifications.

The RS!Regulate GKR-10MS Handguard

The red stock set had to go. That was the plan from day one. I only bought it because it was the first AK-E model that I was available during my daily “do they have one yet” check of the PSA website [click here if you are hunting for one as well].

In place of the handguards, I planned to install one of the RS!Regulate GKR-10MS aluminum rails. It’s 10″ long, is ready for MLOK attachments and looked wicked. Furthermore, you do not need to remove the sling loop on the lower handguard retainer. Scot Hoskisson is the owner and I’ve used his scope mounts on a number of rifles plus one of his handguards on my IWI Galil Ace pistol and really liked it.

I thought this would be easy but that turned out not to be the case due to a seemingly small change PSA made that I’ll cover in a moment. Basically the rail system has three parts – The F1 front piece, the middle rail section and a rear end cap. Scot provides good instructions so follow them to the letter.

Like other AK rifles, there is a space between the front trunnion and the receiver to allow the tab of the handguard to press into. The flakes you see in the photo are presumably from the finish of the red handguard, just FYI.
The block is designed to be filed to fit. You can see where it will go but you will need to take your time and file it to fit.
The elevated sides of the U in the middle need to be filed to fit and you might need to take some off the sides as well.
So take your time, remove a little and test fit over and over. A trick I learned that I applied is to file the protrusions at a very slight angle so that as the handguard is pressed further in, the tighter the fit becomes.
It was coming together nicely. Notice the rail is secured to the end cap and is clearing the handguard retainer nicely in terms of the slot.
Next, this F1 nosepiece has to slide back inside the handguard, get screwed in place and then set screws on the opposite side are tightened thus locking everything in place This is where things go sour.
Every time I tightened down the bottom screw, the F1 piece would cam backwards vs. sitting properly. I tried a few times and could not get it to sit. I have both carpal tunnel and a tremor so this is very tedious for me to try and do. I reached out to Scot and he told me a compatability issue had come up with the PSA handguard retainer.
Due to ever so slight dimension differences, the F1 piece does not sit flush or even lower than the retainer so when the bottom screw is tightened down it cams the F1 backwards. Argh!
I spent almost an hour of careful filing and test fitting and finally decided to super glue a trimmed #6 washer to the bottom of the F1 unit to address the issue. I think this would have worked from the start. Note, Scot tells me that he plans to make a PSA specific unit. It’s totally do-able as-is once you realize you need to add a spacer to the unit. It was rock solid after I made that change and tightened down the set screws. I also had to use a longer 8-32 screw vs. the supplied unit due to the spacer.
Folks, this is the type of washer I used – literally it came out of this box. I ground two flat sides so it wouldn’t stick out past the front or back of the F1 part. Your goal is for the washer to make contact with the handuard before the retainer does. If the retainer hits first, it will want to make the F1 part cant as you tighten it.
Look closely at the F1 fitting in front of the handguard retainer inside the rail – you can see the shiny #6 washer doing its job.

One Of Our Gas Tube Covers

I made a bunch of new molds to make AKM gas tube covers and they are all based on Polish AKM units. In other words, the masters were real Polish covers that I then used to make the molds. It turns out that the PSA gas tube cover is just a tad taller and uses a different spring clip than the Polish units. Our new covers work just fine – the difference surprised me though.

Here’s an original wood Polish AKM gas tube cover on the left and the PSA model on the right. Note the PSA unit is just a tad taller.
To remove the PSA cover, you just rotate it on the tube 180 degrees and pull them off. Because the rifle is brand new, this is very easy to do. On surplus rifles you can have a real fight on your hands trying to get them off sometimes.
Here’s a photo of the installed GKR-10MS rail and our gas tube cover.

One Of Our Russian AK-12 Grips

To change the pistol grip, you remove this bolt and then the T-nut inside will flop around.
This is the loose T-nut that sticks through the receiver. When you install the new grip, use one finger to keep this in place while you are getting the bolt started.
This is our custom US-made AK-12 grip.

M4 Adapter and a Magpul ACS Stock

Next up was the stock. I really prefer the M4-style adjustable stocks and the Magpul ACS is really my go-to unit for most of my builds. It’s solid and has a locking clamp so there is no wiggle.

To remove the stock, first take out these three blade screws. Now, to avoid chewing them up, use a screwdriver blade bit that completely fills the slot from top to bottom and left to right. Using a screw driver that is too small will cause the metal to deform around the screw heads and make a mess. Furthermore, screw driver bits are hollow ground so their end is not tapered unlike a normal screwdriver is.
One of the reasons I keep this Weaver tool set handy is the bit collection. Note how there are a variety of sizes of blade bits. This is my go-to for removing stocks for that very reason.
The stock is press fit into the receiver. It should either just pull out or you may need to use a mallet and wood dowel to tap it out. Surplus AK buttstocks can be a bear to remove but since the AK-E is brand new, you will probably find it fairly easy. In this photo, you can see what some call the “puzzle piece” or “jigsaw puzzle piece” that is unique to PSA. This lets them have one rear trunnion and if the application does not warrant the tang, then it is not installed. Historically, we would have needed to cut that off depending on what type of buttstock system we planned on using. In this build, I am going to use an M4 adapter and I do need the tang so I was careful not to lose it.
If you are now thinking, “crap, I lost the puzzle piece/rear tang” then you are in luck. PSA sells just that part. Click here to go to the product page.
This M4 adapter was on my AK-V. It is either made for PSA by Rifle Dynamics (RD) or it looks just like RD’s design. Basically it slides in place of the stock and the tang of the stock passes through the M4 buffer tube’s mouth. This was an ingenious move and created a short solid adapter. PSA does sell this – click here for the product listing. Unfortunately it is out of stock a lot probably due to the popularity of their rifles and pistols that use it. I’ve used the RD adapter and it is rock solid so I definitely recommend getting that one if you can – check out Brownells or RD directly.
Here’s a view of the adapter from the rear. You can see the tang passes through the threaded circle where the buffer tube will screw in.
The adapter goes where the stock was at using the supplied machine screws. Apply blue loctite so they don’t vibrate loose.
You can see the puzzle piece / modular rear tang is installed and is protruding through the threaded attachment for the buffer tube. Be sure to apply blue loctite to this screw also.
When I need AR parts in a rush, Primary Arms is one of the vendors I check first. They ship fast – often the same day if not the next. This is an Expo Arms 6 position Mil-Spec buffer tube, an Expo Arms castle nut and a BCM Gunfighter QD End Plate (meaning it is an M4 receiver end plate but it has the attachment point for a QD swivel.
On an AR, I worry about torque specs for the castle nut. On an AKM with a sheet metal receiver, you will see it start to twist as you apply more more torque so my recommendation is *not* to treat it like an AR because I don’t want to bend the receiver. I tighten the castle nut down farmer firm (meaning snug and then some) and then stake the nut to the end plate to keep it from moving.
These are my three key tools for installing a Magpul ACS buttstock as well as the tube and cast nut. The above is an automatic center punch. It’s be Neiko and I also have one from General Tools. I use them for staking the castle nut by striking the surface 3-4 times. With my tremor I have a hard time with a hammer and center punch, which is what most folks use. To tighten the castle nut, I use a Magpul wrench. The way it engages the castle nut is very well thought out and reduces the odds of the tool slipping and marring the finish. The bottom is a simple tool I make and sell to grab the friction locking mechanism of the ACS stock and lift it high enough so the stock can slide into place. Yes, there are other ways of doing it but the tool makes it super simple.
Here’s the installed ACS stock
While the AK doesn’t have much of a recoil, it can be softened further by adding a Limbsaver recoil pad that simply replaces the OEM Magpul pad that is a fairly hard plastic. You just use a drive to remove the two screws, pull the old pate off, push the screws into the new Limbsaver pad, line the pad up with the stock and drive them into place.
Here’s the installed Limbsaver recoil pad. It fits very nicely as you can see.

RS!Regulate Optics Mount and Vortex Crossfire Red Dot

In my honest opinion, the best AK mounting rail system is made by RS!Regulate. It’s a two part modular system that Scot developed. It consists of a lower that is tailored to the rifle and shooter preferences that is then mated with an upper that can be optic specific or a general Picatinny rail.

For this rifle, I opted for the full length AK-303M lower and AKR upper. If RS!Regulate is out, check out Primary Arms and Brownells as well..

This is the AK-303M lower. The clamp is adjusted by compressing the clamping bar and turning that silver shiny screw that is then exposed. Clockwise tightens it and counter-clockwise loosens the clamp. I had to dial it in a bit for the PSA clamp and you probably will for just about any rifle. It’s nice and snug now.
Here’s another view of the AK-303M. The top AKR will mount onto the lower and be screwed into place. When everything is dialed in, the rail can be drilled and a roll pin installed to permanently marry the upper and lower if you so choose. Yes, that is a picatinny rail. The upper mounts to it by have the inverse of the rail that then marries together.
Here are the two halves mated together with a Vortex Crossfire Red Dot. The Crossfire red dot is my go-to when I need a good basic red dot optic. I may change it out for a 1-6 or 1-8 scope but time will tell.

Streamlight 88058 Protac Rail Mount 1

The last tweak I did was to add a short piece of aluminum Magpul rail and a Streamlight 88058 Protac Mount 1 light. I have found Streamlights to be very reliable and I use them on a variety of weapons. This model is dedicated for a rail and comes with a pigtail and pressure switch if you want to mount the switch remote from the light. I am right handed, not a huge fan of vertical grips and find it very easy to reach up with my left thumb and turn the light on or off.

The 88061 is a 350 lumen LED light that can use either a AA battery or a CR123A – I prefer the CR123A batteries – it is brighter and lasts longer than if you use the AA battery. Regardless it is cool to know that you have an option in case you are out of your preferred battery but have the other.

By the way, you can see the quick disconnect (QD) sling swivel in the background. This is an example of a part where you do not want to go cheap. The unit seen above is Midwest Industries. Go with a name brand and not some cheap knock-off.

Conclusion

That’s it for now and I hope you found this helpful. I’ll do one more post with photos of the finished rifle.

Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

PSA AK Webstore Links

Interested in an American made AK? Consider Palmetto State Armory (PSA) as a source. Click on the following links for the associated webstore categories for AK-related rifles, pistols and parts at PSA:

AK & Related Rifles

PSA AK-E Part 3: Tear Down and More Detailed Observations

In my last post, I showed you a bunch of photos with my observations of the AK-E right out of the box. In this post, I am going to take it apart and see what I see. Like the last post, I’ll post photos with my thoughts in the captions.

I’m going to be upfront and tell you what I found in terms of flaws or things you ought to be aware of. With that said, this is the smoothest cycling AK with the best trigger out of the box without any lubrication at all that I have ever felt – my IWI Galil Ace was this way also.

So, let’s get to it…

You push in the protruding button of the recoil spring assembly to do the takedown. Note the proprietary jigsaw puzzle piece rear tang that PSA uses. It allows them to have one trunnion and the flexibility to support different types of stocks. Note the slightly bent edges of the screw’s slot. I really wish guys would use the proper sized screw driver to switch to a different type of fastener. This one’s not too bad but the inside ones are worse.
It has a basic stamped dust cover with beading to stiffen it.
Here’s the top of the dust cover. The beading definitely stiffens the cover up.
Here’s our first peek inside. Note the marking on the shoulder of the front trunnion. You have a clear view of the top of the Nickel Boron (Ni-B) coated bolt carrier and the bolt is sitting just in front of the ALG AKT hammer.
Good view of the characters on top of the trunnion. The AKE-0393 is the SN. Note the Ni-B coating is very consistent. You can see the hammer is solidly engaging the bolt and firing pin.
The recoil/operating spring is captured on a two-piece wire assembly just like other AKMs.
The wood is fit nicely. I mentioned earlier the external screw head was messed up just a bit and now you can see the internal two that have their slots messed up more. This happens from using two small of a screw driver. The assemblers need to use the proper sized driver. Note the split rear trunnion where the forward rivets are.
Close up view of the ALG EKT-EL trigger. You can tell this is the enhanced trigger vs the ultimate because the trigger does not have the Ni-B coating that the ultimate does. Note that is has the auxiliary trigger spring installed – that is the single wound spring at the top of the photo. According to ALG, it adds 10-14oz of pull over the normal AK spring by itself. Also note that the select/safety lever can sit fully on trigger without needing the optional roll pin that ALG includes with the aftermarket trigger to allow builders to accommodate different lengths of selector stop bars.
Here’s the hammer in the cocked position held by the hook. The manganese phosphate (parkerized) finish is notably smooth. If it wasn’t, there wold be a grittiness. It’s a very nice trigger. You can see the leg of the auxiliary spring pushing down on the top trigger leg in the photo – it’s the single would spring just forward of the double wound spring.

In case you are wondering, I collected a sample of 10 trigger pulls using my Lyman Digital Trigger Pull Gauge. Weights varied from 4lbs 1oz to 4lbs 12oz. The average was 4lbs 5oz. If someone wanted a lighter pull, then you could remove the auxiliary spring located on the trigger and probably be down in the 3 pound range. I like the feel of the trigger currently and am going to leave the spring in for now.

Boy it looks gorgeous from the top. I like that I can see the gas piston rivet easily – they are a bear when you have to hunt for them. The Ni-B treatment is consistent. The bolt and carrier have serial numbers that match the receiver and trunnion. For those new to the AK platform, the barrel is pressed into the trunnion to the point that the headspace is correct with the bolt that is matched to it. Once the headspace is correct, a hole is drilled and cross pin installed to lock the barrel in place. In the old days, this had to be done because loose manufacturing tolerances could not guarantee that all barrel, trunnion and bolt combinations would headspace correctly. Reliability issues would happen if parts were mixed from different rifles so this led to serializing the parts. By putting a serial number on the parts, an armorer could be sure to put the matching parts back in the correct rifle.
Here’s a view of the bottom of the bolt carrier with the bolt fully forward.
You can see the machining marks very clearly. This did surprise me – I would have expected it to be smooth but the action itself seems to not have any issues. I very carefully watched the bolt head cam travel in the carrier’s channel and it does not hang up anywhere. So, it might not look very good but it does not appear to harm functioning at all.
Here’s another view of the tool marks.
Here’s the best photo I can get with my phone. Everything clears. Time will tell how the Ni-B coating holds up. It appears to be well implemented.
First view of the bolt
Second view of the bolt body
The gas piston’s face is slightly concave.
Here’s the famous Fabrique Nationale Herstal (FN) barrel that everyone is ogling over. As I understand them, the markings mean: HF=Hammer Forged MP=Magnetic Particle tested CL=Chrome Lined 7.62×39 is the chambering and 1/9.45 is the twist rate.

Now you may be wondering, how on Earth did FN pick such an odd twist rate. In short, that is the conversion of “1 turn in 240mm” that is the Russian military spec for 7.62×39. Actually, the metric conversion of 240mm to inches gets you “9.44882” and with rounding we get 9.45. If we rewind the clock, it was also the twist rate they used in the Mosin Nagant and they wanted to save money and use the same barrel making machines. [There’s a real cool write up – click here]

The front and rear sights are just what you’d expect.
By applying the bead to the ejector tab, they stiffened the unit. It’s a nice touch that you don’t always see people address.

So, thanks to the quarantine, I can’t take it out and shoot it. My impressions overall are favorable but the proof will be at the range. I think you are getting a solid rifle for the price. Time will tell how they hold up compared to the premium AKs – Veprs and custom builds.

I hope this helps you out. In the next post I’ll write about the customizations I did to fit my tastes.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

PSA AK Webstore Links

Interested in an American made AK? Consider Palmetto State Armory (PSA) as a source. Click on the following links for the associated webstore categories for AK-related rifles, pistols and parts at PSA:

AK & Related Rifles

PSA AK-E Part 2: Out Of The Box Observations and Photos

1 Comment

After researching and deciding to buy the AK-E, I ordered it and then waited about a week. The trick with any of PSA’s AKs these days is finding them in stock. Here’s my tip to you – the email notification is broadcasting the news to a ton of people and anyone may buy before you do. I’d recommend checking their site manually between 10am to 3pm Eastern. Just leave your browser open on the page and hit refresh when you can – say every half hour or hour. It took me a week or two but that’s how I was able to get both my AK-V and AK-E. This approach works for any of their hard-to-find because everyone is buying them AK-series weapons. Click on the below to go straight to the PSA page in a new tab:

For me, it’s really interesting how PSA has jumped with both feet onto the AK bandwagon and are offering different grades and styles to appeal to different levels of shooters.

Getting back to the AK-3, I only waited about a week and Scott Igert, my good friend who owns Michigan Gun Exchange, called me up when the AK-E arrived and I went and got it.

Opening The Box

For this post I took a bunch of pictures to share first impressions and will put them in the captions of each photo.

It’s a good looking rifle. The red furniture is brighter than I care for but I bought the rifle with the knowledge that I literally planned to replace everything so my strategy was to get the first AK-E that I could get and move ahead from there. Note, PSA packed it well. It comes in this foam lined box and note the little buffer on the end of the charging handle to keep it from poking through the packaging.
Yeah, it’s really red! Note the AK-74 style lightening cut on the stock. The wood is really light. I’m not sure what they used but when you pull the stock, it is surprisingly light.
You can see the little orange chamber flag they include. The front sight block (FSB) is a combination unit that includes the gas block. Because it is now set back, the brake is secured with a jam nut rather than the traditional detent pin that protrudes from the FSB. The rifle ships with one Magpul 30 round magazine. PSA has been teasing they are going to sell their own line of inexpensive AK magazines and I’m going to keep an eye out for that. Magpul is now on their third generation of AK magazine based on lessons learned for reliability and feedback/desires from the AK community.
You can see the handguards have a slight hand swell. An AKM-style optics rail is ready to go. The grip is basic but functional.
I could have done without the Palmetto logo on the side but at least it is relatively small. Note the good job they did on the rivets and the magazine stabilizer dimples. The bluing is nicely done. Fitment of the handguard is good as well.

The muzzle device has two ports on each side and is secured by a jam nut. PSA reports the thread is the standard 14mm x 1mm left hand thread that one would expect on an AK. That means you can use other muzzle devices if you want. I’m going to try and the supplied brake out first before I change anything.

Here’s a closer look of the combo front sight block (FSB). It’s pinned in place and looks good. Note there are no additional vent holes in the gas tube. Some AK variants have them and some don’t – it’s just an observation
Closer view of the side mount optics rail. You can also see the ALG AKT trigger and more of the nicely done rivets. By the way, the AK-E has the best out of the box trigger I have encountered. I’ve been an ALG fan for a few years now and am happy to see PSA use them.
Here’s a closer view of the trigger, selector stop, trigger guard and the magazine catch. Note the cracked pistol grip. I contacted customer service and they offered to either send me a replacement grip with the risk of the shade of red not matching or a $30 credit back to my card. I opted for the $30 credit as I did not plan on keeping it anyways.
Here’s the selector lever. You can also see the nickel-boron (Ni-B) coated bolt carrier. Folks, the rifle arrived unlubricated but it was one of the slickest actions I have felt out of the box. My Galil Ace was that smooth and my Vepr was after I lubricated it. Point being is the Ni-B coating definitely aided lubricity as one would expect.
Definitely a good looking AK.
The manufacturer info is forward of the mag well. You can see the Ni-B coated bolt carrier and part of the bolt itself. Also note that they dimpled the ejector to reinforce it.
The pistol grip is attached via a screw with a washer.

The rear sling mount. You can see the metal butt cap wrapping around the end.

Note the FSB does not have any provision for a cleaning rod. No big deal to me. I have never actually used the supplied cleaning rod on any of my AKs. I either use a Tipton cleaning rod or a bore snake. I honest prefer bore snakes at this point.

So those are my out of the box impressions. In my next post, I’ll begin tearing down and making much more detailed comments about the internals.

I hope you found this post interesting.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.