Back in August 2021, I bought a Tavor X95 and everybody told me to switch the stock trigger cartridge. I did some research and at that time people were recommending Timney or Geissele. My first choice was honestly Geissele because I really like their AR triggers but I couldn’t find them. Timney was the same way so I ordered both – I ordered the Timney on 8/17/21 direct from them and they shipped on 10/6/21. I also backordered a Geissele Super Sabra 05-267 with the thought that I could write a blog post at some point and compare them. The Timney arrived first and that’s what I installed and used up until yesterday. Let me explain.
I took my daughter’s fiancé, Kris, visiting from out of town to our local Berrien County Sportsman’s Club range for a few hours of shooting. The Timney trigger pack was in the Tavor and has been since I bought the Tavor. It has maybe 300-400 rounds through it – I’ve not shot it since I posted about taking it to the range last fall and the great time we had. At any rate, we shot a number of pistols and then it was rifle time – I told Kris that the Tavor is my favorite rifle right now and we start shooting.
I shot about 5 rounds to show the controls and make sure everything was good. I then handed it to Kris who then shot a few rounds and then things got weird. He pulled the trigger and nothing happened. I took the Tavor from him, and explained how to safely handle misfires and ejected the round. There was a barely noticeable dent on the primer. “Huh” I thought – must be a flaky hard primer. I loaded it again and tried – same thing. I took the round to the range’s misfire tube and dropped it down the pipe.
I cycled the Tavor empty, it seemed okay, I then inserted a mag and made sure it was fully seated, handed the X95 to Kris who then charged it, we made sure the bolt was all the way home and he pulled the trigger. Nothing. Okay … something weird was happening. I took the X95 and ejected the round – same thing – a very light dent on the primer. At this point I was beginning to suspect something was wrong with the Tavor – we were shooting Winchester bulk M855 that normally I don’t have any problems with and absolutely never twice in a row.
I had Kris try again and this time I heard something. He would pull the trigger and nothing would happen but when he released trigger there was a delay followed by a click and then if he tried again it would fire. Okay …. something funky was going on inside the Tavor.
I removed all of the ammo and I could replicate it. Something was going on with either the rod that transfers the trigger pull back to the “trigger pack” or “sear mechanism assembly” – what IWI calls the trigger pack – or the trigger pack itself. It was time to pack the rifle up and we moved to an AR I brought that ran just fine.
Taking the X95 Apart
I have a love hate relationship with aftermarket parts. Most of the time when I take and replace a stock part with an aftermarket and something goes wrong, it’s the fault of the aftermarket part. To make a long story short, the problem at the range was caused by the Timney trigger pack.
On a Tavor, the trigger pack normally pulls out very easily once you pull out the two retaining pins. Not this time. It did NOT want to come out. I had to pull pretty forcefully to get it out and the culprit was a big silver dowel/axle pin located in the top front of the pack. Both it and a smaller one in the middle were way out towards the right side. Why? No idea. I tapped both the pins back in with a nylon head soft blow hammer in my Weaver gunsmith kit. I tried to get it to “fire” and it wouldn’t so I switched gears and installed the Geissele Super Sabra instead that was still new in the box.
I lubricated the Super Sabra per their instructions and it dropped right in and worked. So, right now I have an inoperable Timney that I can’t get to do anything on the bench that I think I will try and have Timney do a warranty repair on – I’m kind of curious what they will do or not do. In the mean time, I will happily run the Super Sabra.
The Super Sabra feels really good – I am still using the stock Tavor trigger itself – the part you actually pull with your finger. Geissele sells a replacement trigger but I am not using it – just the replacement Super Sabra trigger pack.
For a bullpup trigger the Super Sabra is quite decent. There is a long pull but it breaks pretty nicely at 4 pounds 12 oz on average. To get that number, I did 10 test pulls with my Wheeler digital gauge. The lightest pull was 4 pounds 2oz and the heaviest was 5 pounds 1 oz. Very manageable and will be what I use going forward.
As I was writing this blog post, I had the Timney trigger pack in front of me. I tried repeatedly to actuate the hammer by pulling on the little lever that connects to the transfer rod in the rifle. Boy, it would not move – not one bit. I’d put a ball pin in the “U” and pull – it would not budge. I just tried again right now and heard a loud click just like we did at the range. I pulled on the lever again while controlling the hammer with my free hand and it “fired” – the hammer came up. In looking inside the cartridge i have no idea what has happened but don’t want to take it apart and void a warranty either. When I closed the hammer, it made a funny clunking abnormal sound and now doesn’t want to open/fire again. Weird. Something has gone wrong, that much I know.
Summary
Not sure what happened but the Timney trigger pack stopped working. I plan on contacting Timney to see if they will look at it under warranty and will report back how it goes – I emailed them on 2/12/2023. I’m now running the Geissele Super Sabra pack and will see how that holds up.
I’m hoping Timney will do a warranty repair so I can compare both units down the road as I had originally hoped. I’ll update the blog post with how that turns out. By the way, I’ve had a number of Timney triggers over the years and this is the first problem I’ve had with one.
3/28/2023 Update: Got a nice update email from Timney. They are revising the design of the disconnector and will start production in June. That’s pretty cool that they are learning and improving their design. They offered me a refund or to wait for the new model and I opted for a refund at this point and they processed it (I bought it direct from them in this case). So, I am happy with the result.
3/25/23 Update: Really not happy with Timney customer service – I sent them polite emails asking for a status or even if they have the trigger (I can see they do from the tracking #) but they don’t even reply. Last email I told them I don’t mind waiting but please give me an idea of the lead time – no reply. I literally have no idea of the turn around time – they never gave me an estimate.
2/17/23 Update: Timney customer service was really easy to work with. They asked me to send them the trigger pack and they would take care of it. So, I sent it via priority mail with insurance on 2/16. I’m curious if they will tell me what went wrong.
Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.
If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com . Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.