Tag Archives: Arm Brace

Installing the CNC Warrior M92 Folding Arm Brace – So Sweet!!!!!!

Next up on the agenda was to install the CNC Warrior folding M92 arm brace.  This thing is wickedly well done and if you get it plus the optional installation kit, just about anyone comfortable with using a drill can do it.

The following is a quick photo of the installation kit – you will need a hand drill and some cutting oil – I like Tap Magic but just about any oil will do vs. running dry and overheating stuff.  You do not want to work harden the sheet metal of the receiver — use cutting oil and keep it cool!

DSC_0211

DSC_0213

SAFETY STEP – MAKE SURE THE WEAPON IS UNLOADED.  NEVER ASSUME THAT IT IS – VERIFY IT IS UNLOADED BEFORE YOU BEGIN WORK.

1.  Make sure your weapon is securely mounted and that you can have ready access to the rear.  The PAP buttstock drill kit has this handy little jig block to help you locate where to drill the small starter hole.

DSC_0214

DSC_0217

2.  With the jig in place, put in some cutting oil and drill the hole.  Note, I am just using a plain Ryobi 18volt hand drill.  The big bit is 3/8″ and I think 12 volt or better could do the job.  The small hole will help you locate and drill with the bigger 3/8″ bit.

DSC_0218

DSC_0220

DSC_0222

DSC_0223

DSC_0224

3.  Be sure to read the instructions and the caution to go real slow with the 3/8″ bit because if you try to go fast, your bit is apt to grab and thread straight into the receiver.  If this happens then you can’t drill the hole as the bit is grabbed and goes in like a powered screw with a boatload of torque.  Now, I did make this mistake but I knew how to get out – I grabbed a 3/8″ cobalt end mill, checked it in my drill and cut the big offending tabs right out of the hole.  If you run into this, you would need to either get an end mill bit or try using various Dremel bits to remove what is left.

DSC_0225

DSC_0228

Unless you have a milling machine, I would not recommend drilling the hole with the end mill – just use it for clean up if needed.  I just used it to clean the bottom of the hole and I used cutting fluid.

DSC_0230

The following is a link to a well regarded carbide mill that will work just fine in this situation.

DSC_0231

4.  My next steps were to use a deburring tool to make sure I didn’t leave anything nasty and sharp in the hole waiting to cut me!  I also vacuumed out the inside of the pistol and made sure it was clean.

DSC_0232

5.  The folder is connected to the receiver via a threaded block that is inserted into the receiver and you then thread the large allen screw into it.  Be sure to line things up and apply Blue Loctite so it will not come loose over time.

DSC_0234

DSC_0235

DSC_0236

DSC_0238

DSC_0239

That’s all there was to it!!  This is a very well done piece of gear guys.  The folder mechanism is solid and the brace feels great either on the shoulder or on the arm plus you can fold it out the way.  Note the quick release sling swivel.  I used one of my Troy swivels – the folder has the hole to use one but it is up to you as to whether you want one or not.

DSC_0272

One last comment – I am keeping the printed copy of the ATF approval letter (that comes with the brace) in my case with the M92 to show anyone who asks that the brace is not a buttstock and this the M92 is not a SBR.  You might want to do the same.

By the way, for any of you wondering why I am using all these CNC Warrior parts on this build – the answer is simple – they make really good stuff and this is my personal M92.  I only want solid reliable stuff on it.


Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at info@roninsgrips.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.