Tag Archives: M92 PAP

Another great accessory for the Yugo M92 or M85 PAP is the slick picatinny rail kit that CNC Warrior sells. This thing is a breeze to install and is the best means I have seen for adding an optic to the M92. Because the screws are inserted from the rail side, it is superior to other products that require the screws to come in from underneath the dust cover and risk being hit by the bolt carrier.

All you need is the pistol, a drill and some cutting oil to do the installation.

SAFETY STEP – MAKE SURE THE WEAPON IS UNLOADED. NEVER ASSUME THAT IT IS – VERIFY IT IS UNLOADED BEFORE YOU BEGIN WORK.

1. This is the top thick hinge of the M85/M92 dust cover. See the faint circles? Those are the spot welds and they are very hard! Do not drill into them! The new CNC Warrior mount has four holes and you only need to use two of them. The reason there is four is so you can pick the best two that get you around/away from the spot welds. Please note that my rail is only silver because it was a brand new design and they hadn’t applied a finish yet. If you order one, you will get a black rail!

2. Here you can see my fancy high tech tools. My Ryobi drill, Tap Magic cutting oil to lubricate the drills and the taps. Note, you will need to buy a tap handle if you do not have one. Do not take the short cut of trying to start the tap with a regular socket or open end wrench. You really want the tap to be firmly held so you can tap the threads at a right angle to the surface of the hinge. Also, see that little black cylinder? That is a drill guide that you put into the hole you select to guide the drill bit to the right place on the hinge. Be sure to use the cutting oil!

3. As an aside, I blasted the mount and then sprayed on flat black Molyresin and baked it. You’d never know it came to me unfinished.

By the way, pictured above is a cheap Harbor Freight air brush. I used to buy a bunch of them at a time and then throw them away when they hard problems. I now use a Paasche H series air brush and am much happier with it.

4. After you clean up the chips and are ready to do the final screwing of the mount, be sure to apply Blue Loctite so it does not come loose.

That’s it! The mount is solid and it holds my Vortex Sparc red dot just great. Note our quick takedown pin to make it easy to remove the cover and get the optic out of the way.

10/27/18 Note: Vortex discontinued the Sparc red dot. They sell a great 2 MOA red dot called the Crossfire that I really like.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Gunsmithing

CNC Warrior’s M92 PAP Picatinny Rail Mount is Excellent!

August 20, 2014 RoninsGrips

A M92 is screaming for an optic of some type. My preference is a red dot and I run a Primary Arms M4 clone on my first rifle and will use a Vortex Sparc on this new rifle.

As some of you may know, I have a Stormwerkz rail on my first M92 that I custom built and it has served me well. The only draw back with the design is that you install the button head screws from inside the dustcover. Because of this, you will notice the bolt carrier does hit screws. I have shot a ton of ammo – well over a thousand rounds – from this rifle and the bolt carrier shows no harm but you do see the scuffed screws.

When I heard that CNC Warrior had a mount, I had to take a closer look and sure enough, they had a different approach. Their screws go through the rail and screw into the thick steel portion of the dust cover that runs to the hinge.

I talked to Denny, the owner of CNC Warrior, about my plans and he recently switched over to a four hole model that will give a person more options when installing the rail to work around the very hard spot welds — basically you just need two screws so with four holes, you pick the two you like that enable you to miss the welds.

If you look closely at the next photo, you will notice small circular indents in the steel – those are the spot welds that are harder than the surrounding steel and can be an absolute bear to drill through. Thus, with CNC Warrior’s new four hole rail, you can slide it back and forth until you get two holes that clear these welds.

Please note that Denny sent me one of each – the old two hole rail and the new four hole rail – so I could show you folks the difference and he did not have time to have it finished so it is bare metal in the photos. I used Molyresin to finish it flat black but that is not something you will need to worry about. Going forward, when you order his mount you’ll get the four hole rail section already finished black.

Included with the picatinny rail is their installation kit and instructions that makes installing it a breeze. In a future blog post I’ll show you just how easy installation is and how you can do it with a hand drill and some cutting oil.

The rail is on their website at: http://www.cncwarrior.com/ProductDetails.asp?ProductCode=26454

Gunsmithing

CNC Warrior Folding Arm Brace for Zastava M92 PAP

August 18, 2014 RoninsGrips

One of the parts I knew I wanted was the folding arm brace from CNC Warrior. This essentially gives you additional support to either fire the pistol with one hand or to even shoulder the weapon comfortably if so desired.

Now the ATF has reviewed and approved the arm brace as not being a shoulder stock. Each arm brace that CNC Warrior ships includes a copy of the ATF letter that says it is not a stock and that attaching it will not make a pistol a SBR.

This stock is a joint design effort between Chris Bonesteel, of Bonesteel Arms and CNC Warrior and is very nicely made. It has a very strong hinge mechanism and is a breeze to install.

When I took the assembly out of the box I immediately noticed how well made it was. I recalled a talk I had several years back with Chris where he worried about some folders being weak and this design reflects that both he and Denny at CNC Warrior wanted to make a strong one. The attention to detail and fitment are very apparent. Hands down, this is my favorite set up that I have seen for the M92.

The following are photos of the brace for people who like to see details:

The following photos shows how nice brace marries up to the back of the receiver plus the quick release sling hole but it has not been attached yet.

It comes with the mounting screw you will need and easy to follow instructions:

I highly recommend you buy their installation kit. It comes with the drill bit and mounting jig to make this a breeze:

In a later blog post, I’ll show you just how easy the installation was. I kid you not, if you have a hand drill and their installation kit, you can do this!!

Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

Uncategorized

New Zastava M92 PAP Pistol Arrived – Of Course It Needs to be Modified!!

August 15, 2014 RoninsGrips

So the Century M92 PAP pistol arrived from via my friend and FFL, Scott Igert, of Modern Antique Firearms. The cool thing about this pistol is that it is actually made in the Zastava factory and is imported here. Zastava originally designed the M92 to be a 7.62x39mm short barreled rifle (SBR) based on the proven Kalashnikov design that could pack a lot of firepower in a small package. To do this, they gave it a short barrel and an underfolder stock.

To make it legal for importation, Zastava opted to go the pistol designation route with the ATF and thus did not install the underfolder plus they spot welded a muzzle nut over the large 26×1.5mm threaded muzzle. Because the muzzle nut was spot welded, they didn’t bother installing the detent pin either.

After getting mine out of the box, I have to tell you that I am very impressed by the quality. This is my second Zastava AK – my first was a Yugo M77 – and both are very well made.

This pistol has received a lot of good attention over the last few years because of its reliability and heritage but it also got negative marks for its weight and being unweildy. Really? I always found those comments funny because of course you are trying to hold a stripped down SBR that weighs about 5.7 pounds empty with one hand!

Now the fun part. The whole reason I am writing this blog post is because these pistols are still available at a reasonable price and there is a very active aftermarket including the grips, handguards and dust cover pin that we make. We’ll have a series of blog posts to step you through how to install the various parts we selected including some wicked parts from CNC Warrior.

Time permitting you will see a few blog posts each week that step you through what I bought, tools and installation.