Tag Archives: PCP

Air & C02 Rifles and Pistols, Turkey

Comparing the Hatsan AT-P2 QE Pistol to the Gladius Long

3 Comments

Before I bought my Hatsan AT-P2 QE Pistol, I did a bunch of research. I wanted a very compact yet powerful and accurate pre-charged pneumatic (PCP) carbine or bullpup that was a repeater for quick and accurate follow up shots for pest control of tree and ground squirrels.

I needed something smaller than my Gladius Long, lighter and did not need the power levels that the Gladius Long bring to the table. The Gladius Long is an absolutely wicked PCP bullpup but for what I need most of the time – discrete firepower to dispatch squirrels and rabbits inside of 12-15 yards most of the time – it was overkill. I love it and am not selling it, but definitely needed a different go-to airgun.

So, I watched a ton of videos and decided on the Hatsan AT P2 and decided to go with the QT-P2 QE Pistol. It was compact, lighter, had solid reviews and had both an adjustable stock and in integral noise moderator built in. Hatsan refers to these as their Quiet Energy (QE) line.

In this next photo, I literally set the AT-P2 QE on top of the Gladius Long and tried to line up the muzzles as best I could so you can see the size difference.

So here’s the comparison of the two:

As you can see the actual package weight including the scope of the AT-P2 QE Tact is 4.6 pounds lighter that the Gladius Long and it is 6-5/8″ shorter.

In terms of energy, I did a lot of reading and can’t tell you for certain. Hatsan themselves says the Gladius Long will produce the following power levels but they don’t tell you the velocity or the weight of the pellet.

From the 2018 Airgun catalog, Hatsan reports the AT-P2 QE in .22 has a muzzle energy of 27 joules. All things being equal, that puts it between power levels 3 and 4 of the Gladius Long. I tend to switch between those two settings so for me, the power of the AT P2 is right in the sweet zone of what I wanted.

In terms of sound, the Gladius is relatively quiet at 3 and louder at 4. The AT-P2 QE is remarkably quiet. To me as the shooter, cocking the pistol is louder than firing it!

Both pistols have the noteworthy Hatsan Quattro adjustable trigger. I thought the trigger of the Gladius Long was the best factory airgun trigger I had tried until shooting the AT-P2 QE. From the factory, it is light! I need to measure it but it is a dream to shoot because I can hold it rock solid on target effortlessly. On the point of accuracy, it can shoot 1/2″ groups at 10 yards over and over using JSB Exact Jumbo Diablo 15.89 grain pellets.

Summary

I’m keeping the Gladius Long for distance shots and/or when I want more power. I will be using the AT-P2 QE for my normal close-in pest work.

6/29/2020 Update: Still very happy with both airguns. We now have replacement fill-probe O-rings and caps to keep your fill probe clean. Click here to learn more.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Turkey

A Video Tour of the Hatsan Factory in Kemalpaşa, Turkey

1 Comment

Hatsan Arms Company is an innovative builder of air guns and shotguns that was founded in 1976 and produce over 300,000 units per year.  Hatsan is located in Kemalpaşa, which is a large town located in the Izmir Province of Turkey.  There they product Hatsan airguns, Escort shotguns and Optima shotguns.

   

One interesting facet of Hatsan is that they handle all facets of production – machining of wood, machining of metal parts, heat treatment, finishing of work such as honing, different types of chemical plating & bluing, injection molding, metal injection, mold making, welding, barrel manufacturing, laser marking, laser engraving on wood & metal parts, camouflage coating, assembly, quality assurance testing, and test shooting.

Hatsan has over 650 workers, 599 machines in 35,000 square meter production area.  To produce products to high standards, Hatsan uses total quality management (TQM) and are ISO 9001 certified.

You’ll note factory looks well used, is relatively organized and bright.

Work centers are organized and appear well equipped.

Substantial automation including a variety of CNC systems.

This is an interesting 5:28 video that showcased their facility in 2015:

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Air & C02 Rifles and Pistols

The Wicked Hatsan AT P2 Pistol / Carbine Combo – Powerful, Compact & Quiet

2 Comments

Hatsan is a Turkish company that was founded in 1976 and makes a number of airguns as well as shotguns. My first Hatsan was .22 Long Gladius Precharged Pneumatic (PCP) bullpup air rifle. The Gladius is amazing but I really wanted to find something smaller and more discrete. Even though the Gladius is a bullpup, it is still fairly big and heavy. I started looking for something else and ran across the Hatsan AT P2 and found what I was looking for.

Hatsan comes up with some radical designs that are well thought out and executed. I was very happy with Gladius so when I saw the AT P2 and that it had their proven Quatro trigger, was a PCP repeater, used their great 10 round magazines, and had integral Quiet Energy baffles, I was pretty much sold but kept reading 🙂

I prefer .22 caliber airguns for dealing with larger pests. The AT P2 claims 780 FPS so that will make around 19.8 ft/lbs of energy at the muzzle. This matters to me because I need the carbine for pest control – chiefly ground squirrels, tree squirrels and rabbits – all of which tear up our gardens. These animals typically need about 3-5 ft/lbs to be dealt with provided accurate shot placement. This means you need an airgun that can put pellets on target in an area of 1″ or less at the range you expect.

I am typically taking care of pests within 10 yards and rarely out to 20. In digging I read reports that the AT P2 was surprisingly accurate, had a good trigger and could hit surprisingly hard with for 10-20 pellets. Unlike the Gladius, there isn’t a power adjustment plus you are talking about a fairly small 50cc air tank compressed to 200 bar (2900 PSI).

Hill Mk4 Hand Pump

Another reason for my buying the AT P2 was that I could continue to use my Hill Mk4 hand pump that really has proven itself to be exemplery. The Gladius and AT P2 use the same air fill probe so I didn’t need to worry about changing probes or buying a second pump.

I actually find the smaller air cylinder works in my favor with the Hill pump. I shoot one magazine and top it off again to 200 bar. It doesn’t take too many pumps to do that compared to a bigger cylinder where you need to put more air into the tank.

UTG 3-9×21 Mil-Dot Bug Buster Scope

So, I ordered the carbine and a UTG 3-9×21 Mil-Dot Bug Buster scope with an adjustable objective. UTG makes great scopes and I’ve used them extensively on airguns and firearms that are not mission critical. I don’t mean this as a negative to UTG – It’s just that I will go to Vortex for those situations.

The Bug Buster scopes are just ideal for this type of application. They are compact, bright, clear and pretty reliable. I’ve had a few over the years and haven’t had one break or fail to hold zero.

They have a number of models of Bug Buster scopes and I don’t think you will be disappointed in any of them. Here’s the one that is on my AT P2:

If I had it to do over, I would buy a scope that has turret for adjusting the illuminated reticle. The push buttons work fine but I prefer the simplicity of a turret – I guess I am just old school. A lit reticle can make a low light shot either early in the morning or at dusk way easier. Here’s what I would recommend:

Plano 1502 Hard Case

I already had a basic Plano 1502 hard case to store everything in. It comes with a little hard case from Hatsan but I wanted to have enough room to put the carbine with the scope attached inside.

The only con in the case of the 1502 is that it has an interior length of 50-7/8″. That is really long relative to the AT P2. I have the stock extended one click and that makes the overall length 32-/34″ and the height from the bottom of the grip to the top of the scope turret is just under 10-1/2″. The AT P2 could have gone in a far smaller case but I made do with what I had.

JSB Exact Jumbo Diablo 15.89gr Pellets

I really like JSB pellets. I’ve shot over a thousand of the 18.23gr pellets through my Gladius. I wanted something lighter to try for better in flight ballistics and less over-penetration so on a gamble I ordered the 15.89 gr pellets.

How did it turn out?

I’m really happy is what it boils down to. I needed to oil the safety lever to smooth it out but other than that, it shoots like a dream. I tell you what, it definitely takes care of tree squirrels – head shots are no problem at all and the trigger is remarkable.

One thing that surprised me is the target grip. It comes with a right hand only grip set that is remarkable comfortable. If you are a Lefty, you can contact Hatsan USA and they will send you a left hand set.

The removable adjustable stock is clearly innovative. I find it way to big to be a pistol plus I want the stability. I didn’t buy it to use without the stock. Removing the stock is simple – push the big detent button and pull straight back.

As mentioned, it is a big pistol as this next photo shows. Unless I was resting it on a fence or something there is no way I would be able to control it. If you have a lot of arm strength and can keep a big pistol steady, then maybe but not me.

The stock can adjust four clicks to be quite long. I just need to go back one click and I am 5′ 8″. The cheek piece is adjustable but I did not need to do so.

This is what it looks like for me:

It’s also remarkably quiet. I haven’t run it side by side with my Gladius to compare the sounds at equivalent feet per second but I can tell you it is way quieter than by Gladius on power setting four. I think the cocking is louder than the report of the airgun and it will put a tree squirrel down hard. Headshots tend to stop in the cranium but heart and lung shots go through the body.

Conclusion

It’s performing exactly the way I had hoped. It is compact, quiet, powerful and also very accurate. I’d definitely recommend it.

If you’d like more comparisons between the Gladius Long and AT P2 QE Pistol, click here.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Air & C02 Rifles and Pistols

The Hatsan Gladius Long Precharged Pneumatic (PCP) Air Rifle and Hill Mk.4 Air Pump One Year Later

3 Comments

I’ve had this Hatsan Gladius Long PCP rifle in .22 caliber and Hill Mk.4 air pump for just over a year now and am very pleased with it for pest control. I have a few observations to share but first if you wish to read any of the original posts, here are the links:

At any rate, I’ve probably put about 750-1,000 pellets through this at least. It really likes the JSB Exact Jumbo Heavy Diabolo 18.13 grain pellets. I can shoot overlapping clusters of holes at 30-50 feet over and over. I have some other weight pellets but haven’t had time to test them. I’m hoping a lighter weight will shoot flatter, expand faster and reduce over-penetration.

From a pressure perspective, the sweet spot seems to be if I keep the cylinder between 170-195 bar, just short of 200. At 200 the first round is a flier. I am not running a regulator on this cylinder. My second cylinder with the regulator is leaking out the end due to some problem from manufacturing that I need to track down some day. It’s not on my top 2,000 list of things to do.

If I had it to do over again, I would not have bothered buying the spare cylinder. I am using this air rifle for pests – mainly squirrels, rabbits and ground squirrels. I can get 16-20 lethal accurate shots and then I refill using my Hill air pump. I never use the second cylinder not to mention the oddball leak out the very end (it’s not an o-ring).

The scope and ring combination has held up great. The scope has held zero. I thought I would use the cheek riser and butt pad adjustments more but haven’t needed them much. I think the cheek piece is up just a hair.

You know, the magazine design is excellent. Some air rifles (Marauder) have real crappy plastic mags and these are metal and easy to fill.

The Hatsan is relatively quiet. I shoot with power setting #4 most of the time and it will drop squirrels and rabbits no problem. There is definitely a muzzle report and I have to worry about over penetration. It blows right through squirrels. On #3, it is remarkably quiet but I have to be very careful with shot placement on a squirrel within 50 feet and I will not use #3 on a rabbit. So most of the time I am on #4 and am very, very careful of what is behind the target. My preference is a tree or something else solid.

I really like the trigger and the safety. The trigger does the job – I haven’t checked the weight but I am able to stay on target with even ground squirrels. The safety lever in the trigger area takes a bit of getting used to but once you do, it is very easy to engage, disengage or check status.

Follow up shots are really nice to have. Up until the Gladius, I only had single shot air rifles. Now I have up to 10 rounds and a side cocking lever that you can quickly actuate while keeping the scope and your eye on the target.

The Hill Mk.4 pump has held up very well. Depending on my mix of #3 and #4 power setting shots, I can top off the cylinder in 25-45 pumps after 10-20 rounds. Because I fiddle with the power settings and I don’t always wait to shoot all 10 pellets I can’t tell you an exact count. By the way, it’s hard to tell if you are down to the last pellet so when I get down near the end of pellets, I will top of the magazine and either top of the tank then or after one more magazine of pellets.

I do periodically put silicone grease on the shaft of the pump and the Hatsan quick connect air fitting. I did find a little zip lock bag and keep the on the air fitting to keep it clean.

I bought this good sized container of silicone grease that is Mission brand and has worked just fine for me. I use it on the Gladius, car work, etc.

In summary, I still like it and am happy with the purchase. Power and accuracy – it’s a great combo and the Hill air pump lets me easily top it off whenever I want to.

6/29/2020 Update: Still very happy with both the Gladius and the Hill pump. We now have replacement fill-probe O-rings and caps to keep your fill probe clean. Click here to learn more.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Air & C02 Rifles and Pistols

Clean Your New Airgun’s Bore Before use

When any projectile weapon is made, there are machining operations, dust and lubricants.  Now a lot of this is down in the bore of your new purchase.  This is true of any arm – including air guns of all types and firearms.  If you shoot your weapon without cleaning it, you do risk hurting the barrel or maybe even a jam.  Think of it this way – all that crud has to go somewhere.  It may go out the end of the barrel or it may get pressed into the walls of the barrel affecting accuracy going forward.

So, clean the barrel.  Now, I’m going to focus on airguns going forward as there are some peculiarities to consider.

#1 – The steel used in air rifles and air pistols is relatively soft – way softer than that found in a firearm.  You must take care not to nick the crown of the muzzle and create a burr that will affect accuracy.  I would recommend aluminum or carbon fiber cleaning rods and not steel.  Look out for the pull through cords as many (not all) have a wire brush as part of the unit.  There are flexible wire units that allow you to pull the patch in from the breach and out the muzzle end.  Personally, I swear by carbon fiber rods and mainly use Tipton brand rods now.  I have 4-5 of them now for different calibers and lengths of barrels.

#2 – Because of the soft steel, do not use any form of wire brushes as they may hurt the rifling and accuracy going forward.  I just use a simple mop for the given caliber that screws into the end of your cleaning rod.  Tip – make sure the thread of your tip(s) match the size of your cleaning rod – for example, that if the rod is 8-32 (size 8 with 32 threads per inch) then the tips should be the same.  I have the following jag set from Tipton.  These impale a patch and allow you to push it down the bore while scrubbing the sides.

#3 – Look out for strong solvents.  I’d recommend something light such as WD40, CLP or any modern synthetic transmission fluid.  If you didn’t know it, automatic transmission fluid (ATF) is a great cleaner and lubricant for airguns and it lubricates the O-Rings.  Regardless of what you use. Run dry patches after to remove any extra lubricant.  By the way, WD40 can help with cleaning but it will not prevent rust.

The following is an example of a clean and dirty mop after going through my brand new Hatsan Gladius and note you would see this from just about any brand and I’m not saying anything bad about Hatsan.  My Gladius is fantastic.  To do the initial cleaning, I used WD40 with the mop and then ran patch after patch after patch until it was relatively clean.  You can decide where you want to stop or you may spend the rest of your life running patches down a barrel.

#4 – This is a bit of a general comment, but be aware of where all the junk is going when cleaning.  For example, don’t use a cleaning and was all the crud down into your action.  Unlike a firearm, it can be nearly impossible to clean from the breach end so you have to clean from the muzzle.  Thus, be sparing with the cleaner and inspect the breach end to see if you need to clean the weapon further.  My advice would be to go light on the cleaner and just make how ever many passes are needed with the mop and/or patches until the bore is shiny.

#5 –  I recommend using a decent gun vise to hold what you are working on to free up your hands.  I sure have cleaned a lot of rifles and pistols over the years sitting on the floor and still do from time to time but the Tipton “Best Gun Vise” has worked well for me.

So with that, you are done.  Guys ask how often should they clean and the answer is surprisingly little – you may choose to do it on a regular preventive basis or when you notice accuracy tapering off.  One thing I had told to me that I took as gospel and will pass on – beware of the harsh cleaners that have ammonia as it will attack/harm aluminum parts in airguns and airguns tend to use a lot of aluminum.

This last comment has to do with lubrication vs. cleaning.  Note, if you are ever lubricating the main spring, areas around the piston or other high pressure areas, you must what is recommended and it is probably some form of  silicone based lubricant vs. petroleum.  Be sure to read up on what is recommended for your application before doing anything in those areas.

In reading the above it sounds like a Tipton commercial but it wasn’t planned – the listed items are what I actually use.  I was not paid to write this.  I’ve bought all my Tipton stuff over the years from Amazon and Midway depending on pricing and availability.

At any rate, I hope these tips help you with your next project.

     

 

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Air & C02 Rifles and Pistols

How to install a Huma Regulator in a Hatsan Gladius Air Cylinder

The Hatsan Gladius is a pretty cool precharged pneumatic (PCP) air rifle.  You get a long of bang for your buck but it does lack an important feature needed to get more consistent accuracy from the rifle – regulated air pressure.

The stock Gladius has a power setting but it does not have a consistent air pressure supply.  What a regulator does is allow you to have the reservoir set at one pressure and then the air fed to the rifle is set at another.  For example, the Gladius’ cylinder is rated for 200 bar (3,000 PSI).  You can set the regulator for 130 bar, which is a popular setting, and you always get 130 bar until the pressure of the cylinder dips below 130 bar.  This not only helps you have a far more consistent pressure but also the number of shots increases because a lesser volume of air is used with each shot due to the regulator.

In talking with folks, the most recommended regulator I could find for the Gladius is made by Huma in the Netherlands.  You can order direct from them, which I did and my two regulators arrived in less than a week.  I should also point out that they were very prompt in replying to my questions, which I really appreciated.

In this blog post I will cover how to install the Huma based on what I learned while trying to install the regular.  I would also recommend that you read the instructions from Huma to make sure you get a better understanding of what is needed.  With the Gladius, installing the regulator is relatively easy because it goes into the removable air cylinder.

Step 1:  Mark the bottom of the cylinder.  I put a piece of tape and marked the bottom of the cylinder while it is screwed all the way into the rifle.  You must do this because the regulator has a top position that must be oriented properly when the cylinder is screwed back in.

Step 2:  Remove the cylinder from the rifle.  It simply unscrews counter-clockwise and you may need to pull the cylinder to overcome resistance caused by the O-Rings.

Here are the instructions but before you do anything – MAKE SURE YOUR CYLINDER IS EMPTY [Click Here For Instructions to “degas” the cylinder].  There is a pressure gauge at the end of the cylinder and it should read zero.

Step 3:  Remove the brass valve assembly end of the cylinder.  Use a 13mm wrench to turn the brass fitting counter-clockwise and unscrew it from the black aluminum tube.  This should turn easily.  If it does not, install the degas tool, turn the set screw and ensure all air is out.  This brass valve assembly should unscrew fairly easily.  If it is taking a lot of torque to turn then this may indicate that the cylinder is still under pressure.  If it is empty and still does not want to turn then there may be a threading issue and you need to decide if you want to apply more force or contact Hatsan.  Again, on my cylinder this came off very easily with me holding the aluminum tube with one hand while turning the 13mm wrench with the other.  The 13mm wrench sits on a flat spot on the valve body made just for this purpose.

Step 4:  Watch out for burs.  The machining inside the cylinder and the valve body are all quite sharp.  Be careful when you are turning things by hand.  If you see any visible burs remove them or you may slit the O-Rings of the regulator by accident.

Step 5.  Prepare the Regulator.  The regulator is one piece.  The online instructions mention and show a separate spacer that is no longer there.  Set the pressure by aligning the brass dial with the pressure markings on the tape.  You would do this by removing the small 3mm screw and using a blade screwdriver to make the adjustment.  I ordered mine set for 130 bar so I didn’t need to do anything but the screw did confuse me as I couldn’t figure out what it was for – it was loose and just sitting there.  I contacted Huma and they told me that this screw is meant to be loose and serves as an air flow restrictor.  To set it, screw it down until it stops and then back it off two full turns.  I had to do this because I removed the screw trying to figure out what it was before I asked Huma.  What I did was hold the screw and rotate the body because that was very easy for me to count two full turns given all the markings.  Huma told me to leave the screw loose so that is what I did.

Step 6.  Grease and seat the bottom O-ring.  Grease everything lightly with silicone grease.  DO NOT USE A PETROLEUM GREASE.  It must be silicone grease to be safe.  Make sure the bottom O-Ring is in place.  This must be done outside of the air cylinder and greased there as well. This is critical – if you do not grease this O-Ring and the bottom of the valve then it may well twist out of position as you tighten things together.

  

Step 7:  Option – notch a small V in the front of the top of the tube to better enable venting. Huma reports there are two ways to make sure the regulator can vent properly.  One is to simply not screw the brass valve back in all the way or take a file and make a tiny notch on the top inside edge of the cylinder before the threads.  I opted to do this as I don’t like the idea of having a loose valve body moving around unpredictably when installing or removing cylinders so I just took a small file and made a tiny notch at the top of the cylinder (opposite from the bottom mark you should have made with the piece of tape).  I did this with the valve sitting horizontally and then wiped out the tiny aluminum shavings and then blew it out too.  I applied the silicone grease after I filed the small notch but took the photo after I greased it so that’s why you see the grease.

Step 8:  Grease everything and insert the regulator.  Ensure the regulator, threads and the first 7mm(ish) of the cylinder after the threads have the silicone grease.  To install the regulator, you must orient it properly.  There is a tiny vent hole in the body of the regulator just below the O-ring that must be at the top of the cylinder where you also made the small notch.  Now the screw end of the regulator goes in first.  So hole up and screw first.  Gently insert the regulator and use a dowel to push the unit into the cylinder.  There will be resistance as the O-Ring pushes past the threads in the cylinder walls.  You really do need a dowel or something to help you push it in while avoiding that bottom O-ring.  If you push on the O-ring with your fingers, it will probably come out — I know this because I did that and it came out and I had to tap the cylinder on my wood work table to get the regulator to come back down so I could fish it out.  What you want to do is slide it down just past the threads.  The air pressure will push it back against the valve body when you fill the cylinder.

 

 

Step 9:  Reinstall the brass valve body.  As mentioned previously, you have two options – either make the notch and screw the body back on all the way or do not thread it back on all the way so the air can vent from the regulator more readily.

Just for reference, if you don’t want to notch the inside edge of your tube, they say to tighten down the brass valve assembly and keep about a business card thickness gap in it.  Again, I made the notch in the top and tightened mine down.

Step 10.  Pressurize and check for leaks.  So, I used my Hill hand pump and gave myself three targets taking breaks at 50, 100 and 150 bar until finally I reach 200 bar.  It is a fair amount of work so take your time, take breaks and let your body weight work for you if you go that route.  At any rate, I checked for leaks at each stop with soap water.  So far, so good.

Now I just need some time so I can do some shooting and compare my unregulated cylinder to my 130 bar regulated cylinder and report the speed, accuracy and air consumption.  That will be for another day.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Air & C02 Rifles and Pistols

How to Degas / Depressurize a Hatsan Gladius Cylinder

The Hatsan Gladius is a really cool bullpup precharged pneumatic (PCP) air rifle.  One really neat feature is that you can simply unscrew the air cylinder and install another.  A second cylinder is way easier to carry around than an air tank of you are hunting or doing pest control.  Also, you can have different cylinders regulated at different pressures that are tuned for combinations of pellets and distances.  Now the base rifle is not regulated and really all a spare cylinder does is give you a backup air source.  I’ll cover installing a Huma regulator in another post but this one will focus on how to degas, or empty, the air cylinder of the Hatsan so maintenance can be done.  For example, if you want to drain moisture, etc.

First, I need to give you a safety message.  A Hatsan Gladius cylinder may contain up to 3,000 PSI of air pressure in it.  This kind of pressure is dangerous.  Do not mess around when you are working with high pressure air (HPA) or you may get injured or killed.  Respect it and be cautious.  If you haven’t read the manual for your Gladius, do so.  If you lost your manual, click here for an online copy at Hatsan.

Okay, depressurizing the cylinder is very, very simple.  Hatsan includes the tool you need in the small white tool box that came in the original case with your rifle.  It consists of a heavy brass cap with a set screw in it and the appropriate sized Allen key.  The first step is to back the set screw out so when you thread it onto the cylinder it does not touch the conical shaped nipple on the end of the cylinder.  The third photo shows what the set screw will look like when you back it out.  You want to be able to screw the brass cap on all the way without that set screw touching.

  

Next, thread the brass tool all the way onto the cylinder by hand.  Do not turn the set screw until the cap is fully seated.  Note the little vent hole shown in the next photo.  This is where the air will vent.

Now, turn the vent hole away from you and do NOT look straight at it to protect your eyes.  Very slowly turn the set screw clock wise.  As it threads into the body of the cap, it will depress the conical nipple and high pressure air will start to vent.  It’s going to act like a jet and you will feel the cylinder move. I don’t advocate cranking it wide open so you don’t blow dust every where and you can maintain control of the cylinder.  It will empty very fast. In the next photo, you can see the set screw turned in.  The only reason the vent hole is showing is for the photo.  Normally I have it turned away from me.

Last step – the cylinder should be empty when you no longer hear air exiting.  Double check the gauge.  To remove the end of the cylinder should be very easy because Hatsan uses some form of silicone grease on the threads and doesn’t tighten it much.  If it is taking a ton of force, double check the gauge as there may be air in the cylinder.

That’s all there is to it.  I hope this helps you out.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.

Air & C02 Rifles and Pistols

Video: Some really good review videos on the Hatsan Gladius

One of my favorite things is to do research.  Before I bought my Hatsan Gladius Long Bullpup in .22, I did a lot of reading and also watching of videos.  Youtube is a goldmine of reviews and insights that one should tap in to.  Here are three videos that helped me learn more about the Gladius and especially get a better look at its features and how loud it was.

The first video is my favorite as the two guys set up the rifle and then go through each power setting and record three shots along with their velocity and calculated foot pounds of energy (FPE) for the pellet they were using.  For some reason they did levels one through five but not six. Regardless, I was pretty much sold by the end of these three videos.

.

.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.