Grill Archives

This past June, my wife and I spotted a big stainless four burner BHG gas grill with a side burner at a neighbor’s house set up for trash pickup. It looked to be in a pretty good shape so I stopped and took a look. The drip pan had rusted away and dropped rust everywhere in the grill plus there was minor rusting elsewhere but it was in very good shape otherwise. My wife asked if I could rehab it because we had a bunch of family coming for a visit a month later. I said “yes” so it went in the back of the Highlander leaving a trail of rust everywhere.

It looked like the grill was used and then left to sit and rust but it was actually in quite good shape. Besides the drip pan, the only other items in tough shape were the heat plates also sometimes called diffusers that sit over the burners. They had rusted significantly and were an eyesore.

What Gas Grill Was It?

“BHG” stands for “Better Homes and Gardens” and the model number was BH13-101-099-01. I don’t really have much more info than that – it’s a big generic stainless grill that was imported from China by Blue Rhino Global Sourcing. You may not recognize the name but when you see their logo – they sell propane tanks, grills and what have you through a ton of stores under their own brand name as well as Mr. Bar-B-Q, Chef Master, Endless Summer, Grill Mark, Mr. Pizza, and Uniflame. BHG is no longer listed by them so one must surmise other brand names were used in the past as well.

According to a sticker, it was made in January of 2013. From there, I bet they were sold through retail stores but I really can’t find any more details after searching but I will say it appeared to be a decently made gas grill.

If you hunt around on a grill, you can almost always find an information sticker that at the very least has the model and maker listed.

Armed with the model number, I could go digging for parts. There is a whole cottage industry of parts suppliers out there when you search but the challenge was finding what I wanted in stock and that the price they wanted plus shipping wasn’t astronomical. In some cases, the part price was low but shipping was sky high.

Note, I also found that most parts places are selling parts that will fit the grill but most advise you to confirm dimensions before you buy. The grill is over 9 years old and these places are selling generic parts – so be sure to check dimensions and even that the seller is legit.

The Drip Pan

Okay, the drip pan was trash. You see, at the end of the day, they are made from steel and salty liquids are dripping on them. If you don’t keep them clean or put foil on top of them, they will eventually rust out.

You need to double check the measurement of your pan – mine was a loose fit in the grill so you have wiggle room in terms of dimensions. Mine was about 15-1/4″ deep x 28-5/8″ wide. The replacement pans will all be in the ballpark but you want to make sure that pan reaches from left to right so it is properly supported.

After a lot of digging looking for an affordable exact match to the original pan, I decided to order a 30″ adjustable pan off of Amazon. The problem I was running into was a combination of the total cost including shipping and also lead times and availability. So, I went with an adjustable model and you know what? It’s just fine.

The AJinTebby pan is 15.5″ deep and can adjust from 27 to 30″ wide. Yes, it is pricey at $46.99 but there is a 5% discount coupon you can apply and if you have Amazon Prime, shipping is free (technically it’s factored into the price but you get the idea – it’s a good deal). Click here to open the Amazon page in a new tab.

An adjustable pan lets you adjust the width to fit your grill. It’s the width that adjusts but not the front to back depth so you still need to make sure of that plus the how much adjustment the model has. The is an AJinTeby 30″ pan that can adjust 27-30″ and has a depth iof 15.5″. It fits the BHG.

The drip pan comes with a nice small drip cup that slides in or out of place under the main pan. Drippings ooze into there and are collected so then you can dump and clean it as needed.

I painted the drip pan and it’s drip cup with Rusto-oleum BBQ & Stove 1200F paint to slow rusting. It has three coats of paint

To further lock and seal things, I put 3M High Temperature Flue Tape on the top of the joints. FYI – the oval hole is where fluids drip through to the aptly named “drip cup” under it that can be emptied as needed.

The Heat Plates

I had to decide what to do with the heat plates. They had rusted to the point of being pretty thin – the heating and lots of salty fluids had really taken their toll on them.

You can see the brand new AjinTebby drip pan under the original heat plates and they looked awful. The grill saw quite a bit of use, that I have no doubt of, and then it sat and rusted even more.

My first thought was to try and save money so painted them with Rustoleum’s Ultra High Temp BBQ paint first to try and save money but I could’t get past all the bumpy look from years of rusting. There are so many affordable replacement options, I decided to go that route.

I painted the heat plates plus I put three coats of Ultra High Temp Rustoleum on the drip pan to slow up the rust. I could have stopped here but the really worn plates were bugging me so I decided to replace them.

The BHG uses 15″ long x 3-13/16″ wide heat plates and they are very readily available in a variety of metals and finishes. I bought a set of five stainless steel replacement heat plates made by Shinestar off of Amazon – click here to open the listing in a new tab.

Here’s a look at the new Shinestar plates prior to installation.

The 15″ Shinestar heat plates are nicely made and are going to last for a long time. I definitely liked them more than the painted ones.

The Gas Regulator Turned Out To Be Bad

During initial testing, the grill ran just fine but then it started getting flaky and finally would barely produce flame. This is usually due to a regular failing and/or rust or a spider web getting stuck somewhere. I pulled the lines and blew everything out with compressed air. Sometimes that fixes the problem but not in this case.

Now, I made a bit of a costly mistake here because I was in a rush. We had an Ace Hardware nearby and I bought a Weber regulator that fit but was a tad short for $44-46 if I recall rgiht. Because it was short, I took a piece of 2×12 lumber and cut a hole in it with a jig saw to hold the tank. A week later, I was in Home Depot and found out they had a ton of gas grill repair parts in stock (I didn’t know they did) including the exact hose and regulator I needed for half the price of the Weber.

The old regulator went straight in to the tank and the Weber unit is at a right angle.

Quick comment – when you are working on gas fittings, there will almost always be a way to support the existing tube/hookup and ou need to do that. See the small nut formed into the black tube? You need to hold that with one wrench while either tightening or loosening the hose fitting. If you don’t support the tube you run the risk of it bending or breaking free. Just remember. always do what you need to do to support what your line is connecting to. Don’t just torque on the hose’s fitting alone.

Because the Weber hose was too short, I took a piece of scrap 2×12 lumber I had, traced the outline of the tank’s botton on it and cut the circle out. Note I drilled four holes so I could start the jig saw blade that did the actual cutting.

There it is – nice and stable. Again, if I had known that Home Depot had a bunch of repair parts, I would have taken the busted regulator in there and found a match.

I could have saved even more if I had the time to order a hose and regulator from Amazon. They have them for $15-18 depending on the length of hose you need. Click here for to open a new browser tab with the Amazon listings – be sure to get the hose length you need and round up vs. down if need be.

Other Minor Touch Ups

I ran a 180 grit sanding mop in the same direction as the stainless “grain” finish and removed surface rust.
Sprayed the inside of the grill so it looked better
One hinge had a missing Cotter key that I replaced
Put a wire brush wheel in my drill and cleaned up the grill grates so they had a nice clean brushed look

The Result

It turned out quite nice and gave us another grill to use during a family reunion we had during July.

So did the inside. There is a smoker box down on the heat plates to add a bit of smoke flavor.

Here’s the restored BHG next to my pride and joy Chargriller Competition Grill that my kids got me for Father’s Day a few years back and I converted for wood (click here if you want to read more about that).

Conclusion

One man’s trash is another’s treasure I suppose. The grill turned out nice. The only things it really needed were a new drip pan and the regulator replaced.

I hope this post helps you out.

Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.