Tag Archives: M92

James’ Sweet M92 SBR WIth Our Handguards

I think James’ M92 SBR looks pretty wicked!! That’s our handguard set on the front. It looks great James!


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



Mark’s M92 SBR With Our Yugo Grip

Mark’s SBR sure looks great!  He used the original wood furniture and one of our Yugo M70/M92 grips with a black blasted finish.

Here is a link to our grip’s order page – click here to open it in a new tab.


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



Check out Aaron’s sweet M92 SBR with our Handguards

Aaron built this SBR by starting with a Zastava M92 PAP pistol kit and then took it from there.  The results are very clean!


 


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



Check out Jason’s M92 with our Handguard Set

Jason sent me this photo of his Zastava M92 PAP pistol with our handguards – it looks great Jason!!


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



How to remove the Zastava M92 PAP Pistol’s Factory Thread Cover

A few folks have asked how to remove the factory installed thread protector from their M92 PAP pistols.  Zastava does actually thread the pistols and it’s a 26mm diameter x 1.5mm pitch left hand thread (M27x1.5LH is the short cut way to write it) under that cover. These things were installed for importation, ruin the look of the pistol and, fortunately, are very easy to remove if you take your time.

Now I used a Dremel with a cut off wheel.  You could just as easily use a hand file.  For me, I used the thread cover to protect the threads and did not worry if it got scratched.  Cut a little and try to turn the thread cover.  It will turn clockwise to be removed once the weld is broken.  Note, if you decide to use a Dremel and are new to them, practice with your cut off wheel on some scrap metal before doing your pistol.  They can hop around unless you know how to hold and maneuver them.

   

Next, I put the thread protector back on and used a stone wheel in the Dremel to clean up the remains of the weld on the gas block.  Again, if you are new, practice first.  The stone wheel may look simple but they can make a mess real fast if you lose control.  I’ve been using Dremels since 1985 – trust me when I say you should practice first.  Also, I like Dremels and have used them for years.  They have tons of corded and cordless models plus there are other rotary tools on the market if you expect to have very limited use and want to save money.

 

While the steel is clean and shiny, dab the bare metal with cold bluing.  I prefer and recommend Brownell’s Oxpho-Blue liquid.

Burnish it with steel wool, repeat and apply oil.

 

Here you go  – done.  You can screw on a brake or install a detente pin from CNC Warrior.

I hope this helps you out!


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



Check out Fred’s Wicked PAP with Our Lower Handguard

Fred’s PAP looks sweet.  He’s using both our lower handguard and one of our quick takedown pins.

12096112_966797546697463_6327749345760013943_n 12140657_966797396697478_3814043065268174426_n

The handguards are available as sets or individual pieces at:  http://shop.roninsgrips.com/Yugoslavian_c14.htm

The quick takedown pin for the dustcover is at: http://shop.roninsgrips.com/Yugoslavian-M85-M92-PAP-Pistol-Quick-Takedown-Pin-M92QuickTakedownPin.htm

 

Cool M92 NPAP Pistol with Our Quick Takedown Pin

A customer sent in these cool photos of his M92 with our quick takedown pin so he can remove the dust cover quickly and easily.  He reports he started with a basic Yugo NPAP M92 and then he finish it with cerakote OD green, a Magpul grip, Midwest rail, sling mount RFT,  it’s shown with a Kvar mag model that is no longer made.

 

 

m92 2 M92 1

The pin is in out store at:
http://shop.roninsgrips.com/Yugoslavian-M85-M92-PAP-Pistol-Quick-Takedown-Pin-M92QuickTakedownPin.htm

We have an installation tutorial for the pin at:
https://blog.roninsgrips.com/?p=390


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.