A good sling for a rifle is really worth it if you plan on carrying them around much. The challenge can be finding one that is quality made that doesnb’t break the bank in terms of cost. Over the past few years, I’ve found a vendor that makes their slings in the USA and does a really nice job – that group is S2Delta.
S2Delta was founded by two Marine Recon vets in Albuquerque, NM, that offers a variety of accessories includling slings, rifle rests and patches. It also looks like they are working on bringing a Remington 700 short action rifle chassis to market as well. My experience with them focuses on their two point modular slings. Let’s review a few things first.
What do they mean by 1-point vs. 2-point slings?
When you see companies refer to a sling being one or two-point, they are referring to the number of places the sling attaches to the weapon. A one-point sling connects only at one point and exactly where depends on the length of the weapon and the preferences of the operator. For example, a relatively short AR may be attached at the end of the buttstock and swung up into position as needed. I’ve also seen guys run connectors along the stock on purpose built end plates just in front of the castle nut.
A two-point slings connects to the weapon and two points – at forward and rear positions usually. I’ve seen guys run their forward position way out at the end of their handguard or even the front sight. The rear tends to be towards the rear of the stock.
Personally, I tend to run two point slings given how I like to distribute the weight of the weapon and how I swing it up into firing position. If I have something relatively small and light, I might run a one point sling but again, this really depends on what you prefer and you learn this over time.
What is a modular sling?
A sling has to connect to the weapon somehow. These days it might be strapped, clipped, a “mash hook”, snap gate D-ring or some form of quick detach (QD) swivel. Instead of dedicating one sling per method, a modular approach became popular that allows you to take a base sling and then pick the connector of your choice to use at one or both ends. You could also start one way and then change just the end vs. the whole sling.
This helps settle the debate of “what connector is best?” Instead, you let your needs dictate what to use. For example, with MP5s I would use HK hooks. With ARs and AKs with modern furniture, I tend to run QD swivels. Again, it’s up to you and what your weapon can support.
What makes a sling “good”?
Ah yes, the quality section. Years ago, I wanted to carry slings forRonin’s Grips and bought a bunch of import samples and all of them were junk meaning they were made from questionable materials and methods. It dawned on me that bringing another sling to market without a differentiator was pointless so I dropped the idea.
Ok, so what you want to look for is the use of wide heavy duty nylon straps, reliable connectors and slides, plus good stitching in a nutshell. So let’s look at each of these points.
Let’s start with the connectors that attach the sling to the weapon – the cheap no-name or import airsoft-grade slings have connectors of real bad quality. I’ve seen hooks snap, QD swivels jam or disintegrate… I dropped an AR on concrete once when the QD failed for example. The connector is very important.
By the way, remember the Die Hard movie scene withere Bruce Willis’ character is dangling from an HK strap? That was a pretty cool memorable movie scene but I wouldn’t say it should set expectations in reality.
These days, I tend to prefer the QD swivels as most of my rifles have them so I can move a sling around quickly if I need to. Also, if I am cleaning, working on the weapon or even firing from the bench, it’s super easy to disconnect the sling and set it to the side.
For the straps, I prefer nylon and you need them to be at least 1″ to 1.25″ wide to fit swivels, etc. When you get up to the area that will be on your portion, look for 1.5-2″ or even having padding. If you are wearing body armor, the weight is distributed. If you aren’t then the weight of your weapon will only be distributed by the area of the sling that is in contact with how you have it slung on your body. A weapon can get uncomfortable surprisingly fast if the weight isn’t distributed. For heavier long range rifles, I will either get a sling with a pad or buy a pad to help spread out the load.
Another thing to consider are the slides, D-rings and other strap management parts – cheap ones tend to be thin and flimsy while the quality parts tend to be beefy and a reinforced plastic.
Last but not least, look at the stitching. Edges should be double stitiched and ends box stitched (think of a rectangular box with an X stitched inside extending to each corner.
The end of the day, the sling is only as strong as its weakest component.
Oh – I should mention length. For two point slings look for at least 50-55″. To short and you will not be able to carry the rifle in a patrol postion perpendicular to your body. A rifle over your shoulder may take too long to deply depending on what your use is.
By the way, before you take that comment to be purely tactical. A charter captain I met this summer in Alaska told me the story of his good friend who was nearly killed by a brown bear. The friend had the rifle on his back and couldn’t deploy it hast enough when the brown bear did a surprise charge from the brush. He would have bled to death from the mauling excepthe got real lucky that there just happened to be a helicopter nearby that could medevac him out. The friend still hunts but carries a .44 magnum in a Kenai-style chest holster and has his rifle much more accessible.
Conclusion
I am now using four of their two-point modular slings on a variety of AR configurations ranging from a 16″ defensive carbine up to a 24″ Criterion varmint barreled custom Aero designated marksman’s rifle with a Vortex PST Gen II scope that weighs quite a bit. The first time I tried one was back in 2019.
The S2Delta slings are made in the USA from good materials and I have not had any problems so far. You get a very good level of quality at an affordable price is what it boils down to.
I hope this helps you out.
Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.
If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.