Seeing The Different Dawson Precision Base Plates For Para P16 and RIA A2 HC 9mm and 10mm Double Stack Pistols

I genuinely like the Rock Island Armory (RIA) double stack 10mm pistols. I jumped into the deep end of the pool and started converting some really cool Mec-Gar Para P16 mags for use in the 10mm and .40 S&W pistols for folks who need either 10 or 15 round limited pistols due to unfortunate magazine limit laws where they live. The feed lips must be shortened and reprofiled to work reliably in RIA double stack pistols.

I’ve written about the conversion and you can click here to learn more but I didn’t really show a lot of photos of the different Dawson Precision base plate options. In addition to changing the feed lips, you have to replace the plate because it literally will not fit in the funnel – it’s a show stopper plus it really does need to be longer to allow for positive seating of the mag in the pistol. You could grind the OEM plate down but then you would need to glue/add material so you can fully set it – note, if you do that, leave a hole so you can unlock the plate in the future.

This post also applies to folks who own the RIA A2 HC double stack 9mm pistols. The same base plates are used on the magazines for your pistols as well and the magazine capacity is limited to 15 rounds as a result.

At any rate, here are a number of photos showing the Dawson Precision base plates and get a better idea of their different thicknesses relative to each other as well as when fully seated in the pistol:

The Dawson plates are machined from aluminum and their sizes are how much thicker they are than the original Para P16 base plate shown on the right. The bottom left Dawson plate is their +200 model and the one above it is the +300.
Here are the three Dawson plates next to each other on our converted P16 magazines. The +100 is on the left, +200 in the middle and +300 on the right. They increase the height and weight of the mag but do not increase the capacity.
With our 3rd Gen mags, Mec-Gar started using the left polymer plate and it works great in the RIA pistols. Both it and the +100 Dawson plate sit flush in the RIA mag funnel.
These 15 round windowed mags all have +100 Dawson plates.
This is a +100 Dawson plate in my RIA 52009 Ultra HC 10mm pistol.
This is the +200 base plate.
This is a +300.
This is the 3rd gen polymer Mec-Gar plate that comes on the 10mm/.40 S&W mags for reference. It fits the RIA funnel just fine.

I do need to note something – out of the two to three hundred converted P16 mags I sold, two buyers had pistols where the distance from the mag catch to the bottom of the funnel would not allow the mags with the Dawson plates to fully seat. I gave them full refunds and don’t know if the issue was the mag catch or the fitment of the funnel to the pistol. Again, only two gentlemen out of hundreds. I really do not think it was an issue with the base plates just to be clear – just stacked tolerances going in the wrong direction.

Summary

Dawson Precision makes great base plates for Para P16 and P18 magazines that enable them to fit in the funnel of most RIA high cap 9mm, 10mm and .40 S&W pistols. They come in three sizes and you can choose based on your preference.

If you would like to purchase base plates or a magazine, please click here to go to the section of our website that has them.

Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.