Tag Archives: PAP

How to remove the Zastava M92 PAP Pistol’s Factory Thread Cover

A few folks have asked how to remove the factory installed thread protector from their M92 PAP pistols.  Zastava does actually thread the pistols and it’s a 26mm diameter x 1.5mm pitch left hand thread (M27x1.5LH is the short cut way to write it) under that cover. These things were installed for importation, ruin the look of the pistol and, fortunately, are very easy to remove if you take your time.

Now I used a Dremel with a cut off wheel.  You could just as easily use a hand file.  For me, I used the thread cover to protect the threads and did not worry if it got scratched.  Cut a little and try to turn the thread cover.  It will turn clockwise to be removed once the weld is broken.  Note, if you decide to use a Dremel and are new to them, practice with your cut off wheel on some scrap metal before doing your pistol.  They can hop around unless you know how to hold and maneuver them.

   

Next, I put the thread protector back on and used a stone wheel in the Dremel to clean up the remains of the weld on the gas block.  Again, if you are new, practice first.  The stone wheel may look simple but they can make a mess real fast if you lose control.  I’ve been using Dremels since 1985 – trust me when I say you should practice first.  Also, I like Dremels and have used them for years.  They have tons of corded and cordless models plus there are other rotary tools on the market if you expect to have very limited use and want to save money.

 

While the steel is clean and shiny, dab the bare metal with cold bluing.  I prefer and recommend Brownell’s Oxpho-Blue liquid.

Burnish it with steel wool, repeat and apply oil.

 

Here you go  – done.  You can screw on a brake or install a detente pin from CNC Warrior.

I hope this helps you out!


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



Check out Fred’s Wicked PAP with Our Lower Handguard

Fred’s PAP looks sweet.  He’s using both our lower handguard and one of our quick takedown pins.

12096112_966797546697463_6327749345760013943_n 12140657_966797396697478_3814043065268174426_n

The handguards are available as sets or individual pieces at:  http://shop.roninsgrips.com/Yugoslavian_c14.htm

The quick takedown pin for the dustcover is at: http://shop.roninsgrips.com/Yugoslavian-M85-M92-PAP-Pistol-Quick-Takedown-Pin-M92QuickTakedownPin.htm

 

Scott Igert’s Custom Yugo M92 PAP with Dark Russian Plum Furniture

Scott Igert owns Modern Antique Firearms in Benton Harbor, MI, and is the force behind the Michigan Gun Exchange website.  He replaced the furniture on the below Yugo M92 PAP:

10409049_796182993773403_5320883308574152484_n

The grip is our ARM9 (which is my favorite grip by the way and use it on my own rifles) and he used a Yugo M92 Ferrule Cut furniture set for the handguards.  Both are in our Dark Russian Plum color with a blasted finish for good looks and a sure grip.  I also like the contrast between the black ferrule and the color of the handguards – I think that is a nice accent.

ARM 9 Page: http://shop.roninsgrips.com/Custom-Bulgarian-ARM-9-Grip-Converted-For-All-AKs-w-Screw-BulgyARM9WithScrew.htm

Yugo Ferrule Cut Page: http://shop.roninsgrips.com/Yugoslavian-M85-M92-Ferrule-Cut-Handguard-Sets-M85M92HandguardsFerruleCut.htm


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



Tools That Can Help You Do the M92 Upgrades

In doing this M92, I wanted to use tools that many guys already have or can get without spending a fortune.  I could have used my mill or drill press but I wanted you to see that some simple hand tools are all you need.  The follow are what I used and certainly you can use other tools that work for you.

Dremel Tool with cutoff wheel, abrasive wheel and sanding drum
If you do much gun work, you’ll find a rotary tool to be a huge time saver when used properly.  I have an ancient corded Dremel tool made for Sears plus an 18volt cordless that I use all the time.  You will need some thin cut off wheels for metal, a small abrasive wheel (if you want or do it all with the sanding drum) and a sanding drum.  Because I use my Dremel a lot, I buy the discounted multibit packs when I find them.

DSC_0061

Here are the tools at Amazon:

Dremel 8220-1/28 12-Volt Max Cordless Rotary Tool

 

One thing I would recommend against is buying cheap no-name import bits – they often fall apart or dull real fast.  For the last few years, I have been buying Dremel brand bits off Amazon.  Everything you’ll need is in the below accessory pack:

 

Dremel 710-05 160 Piece Accessory Kit

The one thing I will say here is to practice before you try to actually work on your new pistol.  I can’t stress this enough – please practice first!! A Dremel can scoot around and chew things up if your hands aren’t supported and you don’t know the “feel” of how to cut things.  So please be sure to do some testing and practice before you go near your pistol.  I’ve been using a Dremel for almost 30 years (literally) and I still get surprised from time to time but I know what to do to minimize bad things from resulting due to my experience.

Hand Drill
You just need a plain jane hand drill.  It could be corded or cordless.  Slower is better to avoid heat build up.  You will need to drill a 3/8″ hole for the arm brace and a #21 hole for the picatinny rail screws.  All the work I did was done with my Ryobi 1/2″ 18volt hand drill that I bought from Home Depot and have gotten a ton of use from over the years.

Tap Handle
If you do not have one already, go get a tap handle from your local hardware store.  You will need it to get a good square grip on the #10 tap if you install the CNC Warrior picatinny rail.  Some guys try to go cheap and use a small wrench but the problem is that you will have a very hard time starting the threading squarely.  Spend a few bucks and get a tap handle.

Irwin 12001 T-Handle 1/4-Inch Capacity Tap Wrench

Good Vise
It really pays to have a good vise.  There are so many options out there but make sure it is secure and that if it has steel jaws, that they are padded with leather, wood, plastic or something else that is relatively soft to protect the finish.  It could be a tool vise or even one of the rifle cleaning and maintenance vises such as Tipton’s.  Just make sure that whatever you use is firmly holding the rifle and can’t slide as you drill.   You could drill it into your work bench or use some clamps on the corners.

Tipton Best Gun Vise

I specifically used one of my woodworking vises that is permanently attached to my work bench for this project.  It is like the following and you must add wood to make the actual jaws hence the screw holes in the side plates of the vise:

IRWIN 226361 6-1/2-Inch Woodworkers Vise

Roll Pin Punches
You could use any punch set but I like pin punches as they have a dimple in the face that goes into the roll spring to help center and drive it.  Note, I have watched guys skip using a punch and just tap in the roll pin with a small hammer directly.  The roll pin punches help but are not mandatory.

Grip 9 pc Roll Pin Punch Set

Hammer

I’ll skip the photo 🙂  You just need something to tap the pin punch with.

Cutting Oil

In a pinch you can use regular oil but I like to use Tap Magic for lubricating drill buts and also taps.  This helps them run cooler and last longer

Forney 20857 Cutting Fluid, Industrial Pro Tap Magic, 4-Ounces

 

Cold Blue Solution and QTips

My favorite cold blue is Oxpho Blue liquid from Brownell’s.  There are a lot of other brands out there and guys have told me they like the cold blue solution from Birchwood Casey as well.

Birchwood Casey PSP Gun Blue (3 Ounce)

 

Deburring tool or Sandpaper

The last tool I would recommend is a deburring tool.  It is very handy for clearing drilled holes of burs.  I used it after I drilled the rear of the receiver for example.

SHAVIV 151-29249 Bonus Pack Deburring Tool Kit for Extra Close Work  with Mango IIB Handle (11 Pieces)

The next posts will be about doing the actual work – I promise 🙂

CNC Warrior Brake and Replacement Detent Pin for the Zastava M92 PAP

To be imported, the M92 has a muzzle nut, or muzzle cap, installed over the threads with a single big weld.  It’s obvious where the weld is and guess what?  It can be easily removed and if you look close that will also then clear the detent spring hole as well.

DSC_0048 DSC_0049

There are a few brake options out there for the M92.  Bear in mind that like many Yugo rifles, the designers made the size and thread of the M92’s muzzle unique.  It is left-hand 26mm wide with a 1.5mm pitch thread – definitely an oddball.   At any rate, CNC Warrior makes a four piece Bulgarian style brake that really cuts down on muzzle flash that I have been drooling over for a while plus they make a number of other brakes, adapters and fake cans that can fit that thread.

The following are more detailed photos for you.  By pulling the small locking wire down, the end cap can be unscrewed and the brake disassembled into its four parts – the body, cap, cone and spring.

DSC_0037

DSC_0038

DSC_0039

DSC_0040

DSC_0041

DSC_0042

DSC_0043

They also sell a detent pin kit so you can have the original method to retain the brake as well and it can be installed in literally less than five minutes because the PAP comes with all the holes drilled:

DSC_0033

Click here for our post that shows how to install them.


If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.



CNC Warrior Folding Arm Brace for Zastava M92 PAP

One of the parts I knew I wanted was the folding arm brace from CNC Warrior.  This essentially gives you additional support to either fire the pistol with one hand or to even shoulder the weapon comfortably if so desired.

Now the ATF has reviewed and approved the arm brace as not being a shoulder stock.  Each arm brace that CNC Warrior ships includes a copy of the ATF letter that says it is not a stock and that attaching it will not make a pistol a SBR.

This stock is a joint design effort between Chris Bonesteel, of Bonesteel Arms and CNC Warrior and is very nicely made.  It has a very strong hinge mechanism and is a breeze to install.

When I took the assembly out of the box I immediately noticed how well made it was.  I recalled a talk I had several years back with Chris where he worried about some folders being weak and this design reflects that both he and Denny at CNC Warrior wanted to make a strong one.  The attention to detail and fitment are very apparent.  Hands down, this is my favorite set up that I have seen for the M92.

The following are photos of the brace for people who like to see details:

DSC_0013

DSC_0014

DSC_0015

DSC_0016

DSC_0017

DSC_0018

DSC_0019

The following photos shows how nice brace marries up to the back of the receiver plus the quick release sling hole but it has not been attached yet.

DSC_0021

DSC_0025

It comes with the mounting screw you will need and easy to follow instructions:

DSC_0035

I highly recommend you buy their installation kit.  It comes with the drill bit and mounting jig to make this a breeze:

DSC_0036

In a later blog post, I’ll show you just how easy the installation was. I kid you not, if you have a hand drill and their installation kit, you can do this!!

 


Note, I have to buy all of my parts – nothing here was paid for by sponsors, etc. I do make a small amount if you click on an ad and buy something but that is it. You’re getting my real opinion on stuff.

If you find this post useful, please share the link on Facebook, with your friends, etc. Your support is much appreciated and if you have any feedback, please email me at in**@ro*********.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Impact, Amazon and eBay.